Water ring vacuum pump works 1

First, the use and scope of use SK series water ring vacuum pump and the compressor is used to pump or pressure gas and other non-corrosive, insoluble in water, does not contain solid particles of gas in order to form a closed vacuum container or pressure , To meet the specific requirements of the process equipment. Inhaled or pressured gas is allowed to contain a small amount of liquid. SK series water ring vacuum pumps and compressors are widely used in machinery, petroleum, chemical, pharmaceutical, food, ceramics, sugar, printing and dyeing, metallurgy, environmental protection and electronics industries. Due to the working process, the pump of the gas compression is carried out in an isothermal state, so the pressure delivery or pumping flammable, explosive gas is not prone to danger, so its application is more extensive. Pump model description. For example: SK-122i2J SK said water ring vacuum pump; 12 said the maximum pumping capacity of the pump 12m3 / min (cubic meters / minute) Second, the principle Impeller 3 is eccentrically installed in the pump body 2, A certain height of the water into the working fluid, when the impeller 3 rotates in the direction shown in the figure, the water by the centrifugal force on the pump wall to form a closed rotary ring 5, the upper surface of the water ring and the hub tangent to the water ring The lower inner surface is just in contact with the tip of the blade. At this moment, a crescent-shaped space is formed between the impeller hub and the water ring, and the space is further divided into a plurality of small cavities equal to the number of blades by the impeller. If the upper part of the impeller 0 ° as a starting point, then the impeller at 180 ° before the rotation of the small chamber volume from small to large, and with the end cap on the suction port communicating, the gas pressure in the space decreased, when the gas was Inhalation, when the inhalation end of the small cavity is isolated from the suction port; when the impeller in the 180 ° to 360 ° rotation process, the inner surface of the water ring gradually close to the hub, the small cavity from large to small, the space of gas When the pressure rises above the vent pressure, the gas is vented when the smaller chamber communicates with the vent port. Each rotation of the impeller, the blade space (small cavity) suction, exhaust time, a number of small cavity kept working, so reciprocating, the pump continuously pumping or pressure to send gas. Due to the heat generated during work, it will heat the working water ring and a part of the water is discharged together with the gas. Therefore, during the work process, the pump must be continuously supplied with water to cool and replenish the water consumed in the pump , To meet the pump's job requirements. When the pump exhaust gas is no longer used, one end of the pump exhaust connected to the water separator (can make a water tank instead), the exhaust gas and the part of the water discharged into the water separator, the gas discharged through the exhaust pipe , The water remains in the separator due to gravity and is supplied to the pump for circulation through the return pipe. With the Director of working hours, the working fluid temperature will continue to rise, this time to be added to the steam separator a certain amount of cold water (tap water can be used) to reduce the temperature of the working fluid to ensure that the pump can achieve the required technology Requirements and performance indicators When used as a compressor, the pump exhaust connected to a car separator, the car mixture into the separator automatically separated gas from the exhaust pipe to the desired system and the working fluid through the automatic overflow switch release, Compressed gas, the working fluid is very easy to heat, the exhaust outlet from the pump, the temperature will become higher, so at the bottom of the steam separator, to continue to supply cold water to replenish the hot water was released, while cooling , So that the working fluid temperature will not be too high, so as to ensure the compressor performance, to achieve technical indicators to meet the job requirements. Third, the structure of the pump from the pump body, before and after the end cover, impeller, shaft and other components. The intake pipe and the exhaust pipe are connected with the pump chamber through suction holes and exhaust holes which are arranged on the disk cover on the end cover. The impeller is keyed on the shaft by keys and is eccentrically installed in the pump body. The total gap at both ends of the pump is adjusted by the pad between the pump body and the disk. The clearance between the impeller and the front and rear disks is adjusted by pushing the impeller (SK-1.5 / 3/6) Evenly. The SK-12 pump, shaft and impeller for the interference fit, this gap determined by the front positioning. SK-120 sleeveless, the rest of the structure and SK-6/12/30/42/60/85 the same. The clearance between the impeller end faces and the front and rear discs determines the size of the loss of gas and its ultimate pressure in the flow of gas in the pump chamber from the intake port to the exhaust port. Filler installed in the two end caps, sealing water through the hole in the end cap into the filler, cooling filler and enhance the sealing effect. The additional water needed to form the water ring by the impeller is supplied by the water supply pipe (tap water), and the water supply pipe can also be connected with the water separator to circulate the water supply. If the seal type mechanical seal, the mechanical seal installed in the filler cavity, without packing, packing gland replaced mechanical seal gland, the remaining structure is the same. Bearing by the garden nut fixed on the shaft. In the end cap is installed on the disc, the disc is equipped with suction, exhaust and rubber ball valve. The role of the rubber ball valve is that when the gas pressure between the impeller blades reaches the exhaust pressure, the gas is discharged before the exhaust port to feed the power consumed due to the excessive gas pressure so as to reduce the power consumption. Fourth, equipment description Series water ring vacuum pump and compressor system by the vacuum pump (compressor), coupling, motor, water separator and piping and other components. The working process of the vacuum pump and the compressor and the steam main is as follows: the gas enters the vacuum pump or the compressor from the pipeline through the valve, and then discharged into the separator through the draft tube and into the separator through the separator. When used as a compressor, the mixture of soda and water exiting the compressor is separated in the water separator and the gas is passed through the valve to the system where the compressed gas is to be compressed. The water remains in the separator and the water in the separator passes through Automatic overflow switch to adjust, when the water level is higher than the required water level, the overflow switch is turned on, water overflow from the overflow pipe; when the water level is lower than the required water level, the overflow switch is turned off, the water separator in the water level rise to reach the required level. The working fluid in the vacuum pump or compressor is supplied by the water separator (tap water is also available). The amount of water supply is adjusted by the valve on the water supply pipe. The difference between gas suction and pressure delivery systems is that the internal structure of the water separator is different. Suction gas, the suction port pressure is lower than atmospheric pressure, and the exhaust port pressure is equal to atmospheric pressure, water separator only overflow pipe; pressure delivery of gas, the suction port is atmospheric pressure (also for the vacuum state), the exhaust port The pressure is higher than one atmosphere. To ensure the delivery of gas pressure, the water separator's water level is controlled by the overflow switch.

Automatic Door Kits

Our automatic door kits include 1 motor+gear reducer, 1 belt,7 meter, 1 idle pulley, Microprocessor, 4 sets of carriage blue wheels, 2 sets of floor guides,2pcs remote control, 2 sets belt clamp mounting brackets, 1 power supply harness and cable connectors, 2 locator, Aluminum track whose length is 2.08 meter, 3 meter, or 4 meter.

We are a manufacturer of automatic door openers that are designed to provide people convenience. Automatic Door Systems` drive to provide that level of service is but one of the reasons why automatic doors are becoming more and more popular. Our Automatic Sliding Door systems are modern, space-saving and elegant.

Automatic sliding doors have many basic functions some of which include: automatic mode with full opening width and/or reduced opening width, and exit only for traffic control. The opening of automatic doors can also be adjustable to make the opening width smaller or larger. Important safety functions such as safety sensors prevent the door from shutting if persons or objects are in the detection zone. If the door leaves are inhibited when closing, they are immediately re-opened or if the door leaves are hindered when opening, they are immediately stopped by a safety automatic reversing mechanism.

Our most popular sliding automatic door. Think of this as the go-to door for everyday automation needs. All components fully tested and pre-assembled at factory for fast, trouble-free installation.

Applications: Retail, healthcare, airports, hospitality, clean rooms. Shenzhen Hongfa Automatic Door Co.,Ltd rated door is designed, test and certified to meet your environment needs. automatic slide doors for industrial, commercial, healthcare, and retail use. You will find our automatic sliding doors throughout in a wide variety of locations, including: Hospitals, Airports, Retail centers, Pharmacies, Hotels, Grocery stores, Hardware stores, Sporting goods stores, and more.

Automatic Sliding Doors can either be a single door sliding in one direction or bi-parting doors where each door leaf slides in the opposite direction. They are often used in grocery stores, entrances to shopping malls, hospitals and other applications where you want to provide your customers a hands free, safe and easy access to your building.In addition, one of the biggest benefits of automatic doors is energy savings. Since these doors only open when someone comes in or out of your building, it prevents the loss of energy when a door may otherwise be left open for a long time.

The control device of sliding automatic door contains basic function and extensional function, automatic operation / hold-open/closed/half-open to meet customer needs. Electric sliding door controller has multiple interfaces for complete access control systems for keeping your life and property more safety. Such as: safety beam photocell, electric locks, sensor etc. Its drive devices adopts European technology to integrate motor with gear box, which offers strong driving and reliable operation and increased power output , it can adapt to a large door.

Providing strength, beauty, and technology all in one package, Hongfa's line of automatic sliding doors provides entrance solutions for practically any application. An exclusive feature is Hongfa's sound-dampening track reducing operational noise to a mere whisper and stops vibration resonance that can be transferred to the building structures.

Automatic Door Kits,Automatic Sliding Door Opener,Automatic Sliding Door Operator,High Performance Automatic Door Kits

Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfautodoors.com