For the modern family, the design of the bathroom has long been more than just satisfying the basic functions of use. It has more and more functions, such as bathing, dressing and makeup. At the same time, however, as a functional area with a large amount of water, moisture protection has become the most important point. According to the Xiaobian Building Network Xiaobian, for the bathroom with external windows, the humidity is between 25% and 35% under normal ventilation conditions; after shower, the humidity can reach about 85%. For bathrooms without external windows, the humidity is between 35% and 50% under normal ventilation conditions; the maximum humidity can reach 95% after showering. Therefore, the renovation of the bathroom from the wall and floor tiles, ceiling treatment, pipeline installation and equipment selection should consider the need for waterproof and moisture-proof, and make careful arrangements. Here, Jiuzheng Building Materials Network Xiaobian will share some moisture-proof experience.
Waterproof layer needs to be "digital"
Doing a good job in waterproofing is the top priority of bathroom renovation. Many families may also have this awareness during the renovation, but many people do not know how to supervise the construction workers to complete the construction with quality and quantity. In fact, the easiest way is to master the following data: bathroom wall tiles, stone laying should be made under the surface layer waterproof layer, use cement mortar to level the ground, apply waterproof coating, and then lay a layer of 1:2 cement The mortar is used as a bonding layer, and the floor tiles and other decorative materials are laid up. After watering, the wood is photographed to achieve a flat and firm joint and tight joints. Before the stone is laid, the back coating should be done to reduce the phenomenon of “water stainâ€. The area around the waterproof layer should be turned upside down, about 25 to 30 cm above the ground, the washstand should be 1.0 to 1.2 m above the ground, and the shower should be 1.8 m above the ground. If the paint is decorated, it should be brushed with waterproof putty and waterproof coating. The surface layer of water should be treated to slope to the ground, no water, no leakage after 24 hours storage test.
Ceiling PVC material with caution
There are many types of bathroom ceilings and the materials are varied. Jiuzheng Building Materials Network Xiaobian suggested that the ceiling can be used with micro-aluminum gusset plates to enhance ventilation and prevent condensation. If gypsum board is used as the ceiling, it should be noted that the waterproof putty should be brushed first, then the waterproof coating should be brushed. For some PVC material ceilings, this material is prone to condensate and causes water droplets to drip. It is recommended to use it with caution.
Minimize pipe installation
There are many pipes in the bathroom, and the pipe installation should try to avoid changing the original upper and lower pipes. When the decoration must be changed, it should be horizontal and vertical, firmly laid, and the slope meets the requirements. The valve and the faucet are installed in a straight, flexible and convenient manner, the anti-rust paint is applied to the bright tube, and the anti-corrosive paint is applied to the dark tube. The water supply pipe is tightly connected with accessories and appliances, and there is no leakage through the water test. The Floor Drain design is still based on the above sewer line, and the surface should be slightly lower than the ground.
Appliance selection considers waterproof and moisture proof
The installation position of the bathroom appliance should be correct, and the upper edge of the appliance should be level. Bathroom appliances should be selected from regular brands and have good waterproof performance. For example, shower heaters used in long-term wet environments, the outer casing should be made of stainless steel, with good anti-corrosion performance, and with waterproof power switch, cable and plug, and power-on. Or when the power is off, you are not afraid of water and water splashing, and will not cause leakage or damage. Also need to be equipped with a waterproof lamp cover, waterproof socket and so on.
In addition, the use of wooden materials should be avoided in the bathroom. If it is necessary to use, it should be made of fireproof board or full-mixed oil, which can be waterproof. When making ceilings or other package decoration, the hidden wooden keel needs to be painted with waterproof coating or preservative.
Finally, it is very important that the bathroom maintains a good ventilation. Use better quality ventilation equipment to help the water and steam evaporate quickly and keep the room fresh and clean.
Summary of Jiuzheng Building Materials Network: If you do the above work, you should be able to make your bathroom dry and refuse to be a "tidal person."
Single Handle Kitchen Faucets or taps frequently use one handle, more complex, valve controlled by a single handle (single handle mixer). The handle moves up and down to control the opening and turning off, and moves left and right to control the temperature of the water.
Single Handle Kitchen Faucets,Single Handle Kitchen Sink Mixer Tap,Single Lever Brass Kitchen Faucet,Single Handle Brass Mixer Faucet
Kaiping Jenor Sanitary Ware Co., Ltd , https://www.sanitaryjenor.com